Happy Anniversary to us!

Well, it's only been twenty years. The day slipped by without much ado, as the celebration of choice Dawn made was to have us take the kids to Disney in August (instead of the cruise for two that I gave her for another option).

Another weekend on Dad's house

We finished hanging drywall in 3 1/2 rooms:

Master bedroom (upstairs):



Dining, Living and stairs:




And over half of the guest room:

Beckie's Kitten

Needs a bath after jumping in the toilet as it was being flushed:

Fixing plumbing

Last weekend Bruce pointed out that the old humidifier valve over the water heater was leaking. Finally got around to fixing it (putting a cap in place of the valve), after catching and dumping water for the last 3 days.

Open house + Dress making

Last weekend we had an open house to recognize Adam's graduation from Ferris. Numerous photos are below.








Tonight (Tuesday), Rachel and I were working late into the night to finish her costume to wear to Renaissance Day, where her class was taken to Castle Farms in Charlevoix.
Check out what we managed to sew together over the course of 10 evenings and a weekend:

Memorial weekend working on Dad's

We finished another room today -- we drywalled the other deep closet in the master bedroom.

We also managed to complete 2/3 of the drywall in the master bedroom -- it's actually beginning to look like rooms!

Kitchen with all it's drywall:


Upstairs master bedroom, northwest drywall:

Another weekend on Dad's house

We managed to finish the ceiling insulation in this two-day session, as well as the east wall is now insulated. That leaves very little insulation to complete the actual house.

Part way across the ceiling on Saturday:


The kitchen:



The living and dining rooms:


The finished ceiling:


Grandpa's helper:


Not pictured, we also hung the first 5 sheets of drywall (in the kitchen).

And the Geo installation continues...

Great Lakes was here again today, to plumb the humidifier to get its supply from the hot water heater, as well as add an outlet to power it. They also replaced that bad valve that wouldn't close for the 2nd stage of heat/cool.

The list of things to be completed is smaller (but is taking quite a long time to complete!):
- Consolidate humidistat with new digital unit
- Complete the control wiring

Just look at the dates between these posts! MARCH 27 until today?!?!? Nearly a MONTH!

Added the humidifier

Today they finished up a few more items, and added the humidifier.



Seems the items that need to be finished up are:

• 1 piece of pipe insulation
  
• move the humidifier source from the cold water supply to the warm off the hot water heater
  
• reconnect the control lines for the cutoff control unit
  
• install our back ordered thermostat
  
• tell me why the "small" water output valve is always open, even when the unit is off
  

Now the plumbing

The new unit appears plumbed, and the output plenum is on.



I turned on the unit and the entire family was surprised at just how quite it runs, compared to the old one. It is going to be WAY to quite in the house now!

Out with the old, in with the new!

Well, we've decided to proceed with our Geo-Thermal replacement; the supplier we chose is Great Lakes Plumbing and Heating of Indian River.

Here is day One of the furnace update:

Out with the old:


In with the new:

Easter Sunday

After a nice dinner with the family and when Dawn went off to work, I finished up the "business side" of the downstairs bathroom.

It has been a while since this side has been this clean or useful.



On the vanity side of the bathroom, I've got the old pipe removed and replaced the drywall to get it on it's way to completion. This shows a couple layers of mud on board, and will be ready for some paint "soon"!

Working on Ubuntu setup

A couple weeks ago my brother and sister-in-law gave me an older computer, on which I wanted to set up a home-based web server.

So far, I've managed to get Ubuntu 7.04 "the Feisty Fawn" installed, got vsFTP server running, signed up for a DynDns domain name (WayneRossIs.BoldlyGoingNoWhere.org), set up ddclient to keep that DNS pointed at my current cable-modem's IP address, and now I'm on to setting up a web server.

I am still stumbling on how to get the users I want to have access to my machine. So far, I can sign in within my house and have it work the way I want, but if I go over the cable modem/router the actual file transfer and directory listings don't go through. I poked ports 20 & 21 through my LinkSys, but there seems to be something more that I need to do...

I found a helpful Tutorial here for setting up Apache 2. Didn't take too much effort, and it was up and running a simple set of static web pages in just a few minutes! See the results here!

Following that, I set up SAMBA following this detailed guide, and that was good to go!

Getting things buttoned back up

The utility room is completed now:


Got the drywall back above the toilet. Just have to put the paneling back after I get a white piece of panel seam.

Dishwasher fixed, need new Furnace!

Got the dishwasher put together last night after getting the correct $12 part locally. The girls will be happy to have an easier time of washing the dishes!



The furnace man came today, confirmed the freon leak is in the coaxial coil, leaking into the water system. As the furnace is 15 years old, they suggest the only alternative is to replace the whole furnace (which they'll be happy to do for $8700).

AAAARRRRGGGG!!!!!

Now it's the dishwasher!

At 3am today the dishwasher broke. When it began the discharge cycle, it started making a humongous racket.

We have a Maytag MDB7100AWQ, serial 24135498YZ. The handle of a pot prevented the bottom rotating arm from spinning, and I think it ground some plastic nubs off the bottom side of the Discharge Housing Assembly.

Under this Housing:


I found a flat disc that looks like it is to act as a slip-clutch with tabs on the bottom of the impeller:


What I'm wondering about, is this really a problem (and the shortened tabs mean I need to buy a new part) or is this by design and I need to look for the source of my grinding noise elsewhere?


When I assemble the unit without the flat disc and run the drain cycle, it is rather quite, so I really think this is the problem. Might be I need one of these:

Back to work on the utility room

Since more pressing things seem to have settled down, I've got to get back to fixing up the utility room.

Taurus engine swap - completed!

Well, Adam finished up "our" project today.

To help the engine exchange project along, I spent $400 on insulation at Home Depot and put that up the day before Christmas. We were then able to heat the garage enough to actually be comfortable while working.

Pictures as we went along:
Wednesday, the day after Christmas had the car up:


And the engine out:


Friday:
Upon the recommendation of my mechanic, a new water pump was installed ("easier now than later in the car"):


Getting ready to go in:


Really late Friday night:
Back on the subframe, connected to the transmission:


This is the point that I left it so I could travel to da U.P. to do more Christmas visiting (with MOST of my kids in tow!)

Adam called Sunday morning 8am while I was at the farm to let me hear the car start, as he just finished a marathon session of getting the engine reconnected!


Here is the bad engine, sitting on a trailer just before I took it to the local high school to be used in experiments:

On the way to California...

When leaving Huston, TX for Ontario, California, I boarded the plane in the second group of passengers (First Class first, then Elite).

Sat in 8D (an aisle) until everyone was boarded and situated. It looked like the seat between me and the gal in the window seat was going to be unoccupied. Then the stewardess came up to me with a boarding pass with my name on it, asking “is this you?” I said yes and she went back up front. It took me a minute to see what was different about that pass – it was for 5E – First Class!

Once I figured that out, I moved my butt up front. That was so cool! It was nice to have the bigger seat, food and free drinks while watching the in-flight movie during the 3+ hour flight!

Travel, travel, travel!

I went to St. Louis before Thanksgiving, Columbia, South Carolina a week later, and now have tickets for Ontario, California!

I went through the effort of creating a Google map of "all the job sites I've been to", but have only really accurate records for the last 3 years. Before that are several that were "in a fog", so I have yet to figure out when I went to each.

Anyway, I've create that and here is a link which should always hold the most up-to date version:
Wayne's Google map

In getting ready to go, I went and got a replacement 3L engine for my Taurus from St. Ignace. So, now have even more to keep me busy over Christmas!

Went to Traverse City last night with Dawn and the girls to see the Nutcracker at Interlochen. Ate dinner with "my Tom" at the mall and caught up a bit with him.